Outboard Trim/Tilt Pin Wrench MT0004-38mm x 4mm For Seastar, 4 Stroke Yamaha V6

Description

Application:
Fits all Seastar Steering Cylinders, Trim and Tilt Caps on all Four Stroke Yamaha V6, Trim and Tilt Caps on Non-VMAX 2 Strokes (225-300hp), and Tilt Caps on the 2011-Current F150. This wrench is not compatible with VMAX.
Function:
To rebuild a leaked device on outboard engine, hydraulic trim and tilt unit .Used to remove and install the Trim and Tilt Caps without damaging it and the steering cylinder.
A Must Have:
DR-Auto
Your Best Auto Business Partner
Outboard Trim/Tilt Pin Wrench MT0004-38mm x 4mm Remove Hydraulic Cylinders Trim/Tilt Caps fit for Seastar, Four Stroke Yamaha V6
Application:
Fits all Seastar Steering Cylinders, Trim and Tilt Caps on all Four Stroke Yamaha V6, Trim and Tilt Caps on Non-VMAX 2 Strokes (225-300hp), and Tilt Caps on the 2011-Current F150. This wrench is not compatible with VMAX.
Function:
To rebuild a leaked device on outboard engine, hydraulic trim and tilt unit .Used to remove and install the Trim and Tilt Caps without damaging it and the steering cylinder.
A Must Have:
Usually, you will put a little drift into one of those holes in the trim and tilt caps with a hammer. Than,you destroy these cap ,you will thrown them away,which cost a about hundred bucks. So, you really need the pin wrench to help you finish that case with ease.
High Quality Material:
Made of high hardened 4140 impact grade steel,with silver oxide coating which is rust-resistance and durable to use.Better than OEM.
100% Satisfaction Guarantee:
If you're not 100% satisfied with this pin wrench MT0004, simply return it for a full refund in 60 days, guarantee with 2 Years' warranty.
Product Description:
DR-Auto AMT0004 wrench fits ALL Yamaha, Suzuki, Johnson, Evinrude trim and tilt end caps.
Ultra High Strength stainless steel brings minimum 180 ft-lbs proof strength.
Also works on SeaStar Hydraulic Steering ends caps. If looking at a specific application measure the pin spacing and diameter!
Operate easily, only makes both pin line up with the hole and insert, then work with 1/2" breaker bar.
Item Specifics
Brand
DR-Auto
Type
Outboard Trim/Tilt Pin Wrench
Material
Steel
Number of Pieces
1
Model
MT0004
MPN
DRQP982
Size
38mm x 4mm
Fitment
Fit For Seastar, Four Stroke Yamaha V6
Warranty
2 Year
Payment
1. Payment methods accepted:
Payoneer
.
Our Payoneer account allows you to pay by credit card, debit
card and your paypal balance.
2. Please make sure your
Ebay
address is correct
before you pay, cause it cannot be changed once the order shipped out.
Shipping
1. Item will be shipped out
within 1-2 business day
after clear payment received.
2. Please make sure shipping address on your ebay account is
correct & up-to-date.
3. All of our items are shipped from our warehouse.
4. Please feel free to contact us by email if you cannot get your order in time.
Please read the shipment and payment detail carefully before you bid.
Returns
1. Return to us
within 30 days
from the delivery date for exchange or refund.
Refund will be given as Money back
or item exchange (buyer's choice).
2. Return shipping fee is the responsibility of buyer unless the return is a result of our mistake
.
And all NON-seller mistake returns for refund are subject to
10 % re-stocking fee.
3. If you need return, please
contact
our customer service representative,
let us know the detailed problem and
end us some pictures for confirmation.
Contact Us
We
maintain high standards of
excellence Four 5-star
rating
and strive for
100%
customer satisfaction! Positive Feedback
is very important to us. If you are not satisfied with our product or our Service,please feel free to contact us
immediately BEFORE you leave neutral
or negative
feedback, we will try our best to resolve any problem and make you satisfied.
Please contact us via ebay using"Contact member".
We will respond within 1 business day
or less.Thank you for your understanding.
Our office hours is as below :
- 9:00 a.m. to 6:00 p.m. (GMT +8) of Monday to Friday
- 9:00 a.m. to 1:00 p.m. (GMT +8) of Saturday
And our office is closed on Sunday and public holidays (Hong Kong)
We apologize for the late reply during the holidays.Please contact us via ebay using"Contact member".
We will respond within 1 business day or less.
Please include your ebay item number or order number in
all communications.
DR-Auto
Your Best Auto Business Partner
DESCRIPTION
PAYMENT
SHIPPING
RETURN POLICY
CONTACT US
Shop Category
Store Home
New Arrival !
Engine Tool
Car & Truck Accessories
Generator Accessories
◈  Gas Cap Adapter
◈  Generator Tool Kit
◈  Other
Tool
◈  Home & Garden
◈  Bearing
◈  Engine Tool
◈  Oil Filter Cap
◈  Other
Tail Light Covers
◈  Other
Pool Lights
Parking Reverse Camera
Sunshade & Windshield
Car Keys Fobs & Remotes
Jeep Grand Cherokee
JK Full Set Interior Decorate
Ford Mustang
Boat Parts
Blacksmithing
Other
Boat Parts
Knife Making Tongs Set
Auto Tools/Parts
Crankshaft Gear Front Crank Seal Installer For John Deere 1039,4045,6059 JDG954B
USD 199.97
Trim Rod Assy Kit For Mercury/Mariner Verado 200-300hp IL6 8M0118299 896157A01
USD 139.98
Diesel Piston Ring Compressor 5.4" Bore For Cummins ISX, CAT 3400, C-15, PT-7040
USD 167.39
22Pcs Car PDR Tools Pushrods Spring Kit Paintless Dent Repair Hail Removal Tool
USD 89.36
For Caterpillar CAT C7 C9 3126B Injector Sleeve Cup Removal & Install Tool Kit
USD 136.79
J-47388-A Injector Cup Remover & Installer Tool For Detroit Diesel DD15 & DD13
USD 116.59
PT-6400-C Diesel Cylinder Liner Puller Tool For Caterpillar, Cummins, Volvo etc.
USD 425.69
328.12031 Seal Replacement Kit For Sears Craftsman 2-Ton Floor Jack Hydraulic
USD 59.59
10Pcs Car Body Paintless Dent Repair Tools Push Rods Kit PDR Hail Removal Tool
USD 73.79
303-1513 6.7L Powerstroke Rear Crankshaft Seal Remover Tool For Ford #Alt ST-148
USD 257.99
KK-4835 Air Compressor Piston Kit For Porter Cable Craftsman Devildiss Dewalt
USD 95.02
31 PCS Auto Oil Filter Socket Wrench For Many BMW, Volvo, Honda, Audi, Ford etc.
USD 99.89
Rear Axle Bearing Removal Puller Tool 09521-25011 for Toyota Trucks 1984-2018
USD 166.85
9U-6891 Injector Sleeve Cup Removal Tool Set Fits For CAT 3406E C10/12/15/16/18
USD 91.19
13Pcs Master GM Transmission Bushing Driver Set Tool Kent-Moore SPX T-0220-700R4
USD 98.63
6697 Wheel Knuckle Vacuum Oil Seal Installer Fit For Ford 2005-2019 F-250 F-350
USD 71.97
4918991 Crankshaft Front Seal Wear Sleeve Remover/Installer For Cummins ISX12/15
USD 213.20
Front Crankshaft Oil Seal Remover & Installer Kit For BMW N52 N53 N54 N55 Engine
USD 173.99
Hot Accessories
Outboard Trim/Tilt Pin Wrench MT0004-38mm x 4mm For Seastar, 4 Stroke Yamaha V6
USD 37.79
Outboard Trim/Tilt Pin Wrench MT0006-32mm x 4mm For Yamaha,Suzuki,Johnson,Honda
USD 39.23
Outboard Trim/Tilt Pin Wrench MT0006-32mm x 4mm/4.5mm For Yamaha,Suzuki,Evinrude
USD 42.83
Outboard Trim/Tilt Pin Wrench Set MT0004 MT0006 MT0009 For Yamaha Suzuki Johnson
USD 102.15
Power Trim Tilt Manual Release Valve For Most Mercury 2 & 4 Stroke (Stainless)
USD 19.25
New Arrival
Oil Filter Wrench Cap Removal Tool for Toyota Corolla Prius Scion Matrix 1.8L
USD 7.19
Red Side Door Handle & Push Button Knobs Cover Trim For Jeep Wrangler JK 07-18
USD 25.42
NEW Back Up CCD Rear View Reverse Parking Camera for Toyota 4Runner 2002-2010
USD 22.40
6682 Camshaft Holding Tool Timing Cam Tension Set For Ford 3.5L 3.7L 4V Engine
USD 35.00
Car Windshield Sunshade for 1985-2020 Jeep Wrangler JL JK TJ LJ YJ Sun Visor
USD 18.35
Outboard Trim/Tilt Pin Wrench MT0004-38mm x 4mm Remove Hydraulic Cylinders Trim/Tilt Caps fit for Seastar, Four Stroke Yamaha V6
Application:
Fits all Seastar Steering Cylinders, Trim and Tilt Caps on all Four Stroke Yamaha V6, Trim and Tilt Caps on Non-VMAX 2 Strokes (225-300hp), and Tilt Caps on the 2011-Current F150. This wrench is not compatible with VMAX.
Function:
To rebuild a leaked device on outboard engine, hydraulic trim and tilt unit .Used to remove and install the Trim and Tilt Caps without damaging it and the steering cylinder.
A Must Have:
Usually, you will put a little drift into one of those holes in the trim and tilt caps with a hammer. Than,you destroy these cap ,you will thrown them away,which cost a about hundred bucks. So, you really need the pin wrench to help you finish that case with ease.
High Quality Material:
Made of high hardened 4140 impact grade steel,with silver oxide coating which is rust-resistance and durable to use.Better than OEM.
100% Satisfaction Guarantee:
If you're not 100% satisfied with this pin wrench MT0004, simply return it for a full refund in 60 days, guarantee with 2 Years' warranty.
Product Description:
DR-Auto AMT0004 wrench fits ALL Yamaha, Suzuki, Johnson, Evinrude trim and tilt end caps.
Ultra High Strength stainless steel brings minimum 180 ft-lbs proof strength.
Also works on SeaStar Hydraulic Steering ends caps. If looking at a specific application measure the pin spacing and diameter!
Operate easily, only makes both pin line up with the hole and insert, then work with 1/2" breaker bar.
Payment
Shipping
Returns
Contact Us
1. Payment methods accepted:
Payoneer
.
Our Payoneer account allows you to pay by credit card, debit
card and your paypal balance.
2. Please make sure your
Ebay
address is correct
before you pay, cause it cannot be changed once the order shipped out.
1. Item will be shipped out
within 1-2 business day
after clear payment received.
2. Please make sure shipping address on your ebay account is
correct & up-to-date.
3. All of our items are shipped from our warehouse.
4. Please feel free to contact us by email if you cannot get your order in time.
Please read the shipment and payment detail carefully before you bid.
1. Return to us
within 30 days
from the delivery date for exchange or refund.
Refund will be given as Money back
or item exchange (buyer's choice).
2. Return shipping fee is the responsibility of buyer unless the return is a result of our mistake
.
And all NON-seller mistake returns for refund are subject to
10 % re-stocking fee.
3. If you need return, please
contact
our customer service representative,
let us know the detailed problem and
end us some pictures for confirmation.
We
maintain high standards of
excellence Four 5-star
rating
and strive for
100%
customer satisfaction! Positive Feedback
is very important to us. If you are not satisfied with our product or our Service,please feel free to contact us
immediately BEFORE you leave neutral
or negative
feedback, we will try our best to resolve any problem and make you satisfied.
Please contact us via ebay using"Contact member".
We will respond within 1 business day
or less.Thank you for your understanding.
Our office hours is as below :
- 9:00 a.m. to 6:00 p.m. (GMT +8) of Monday to Friday
- 9:00 a.m. to 1:00 p.m. (GMT +8) of Saturday
And our office is closed on Sunday and public holidays (Hong Kong)
We apologize for the late reply during the holidays.Please contact us via ebay using"Contact member".
We will respond within 1 business day or less.
Please include your ebay item number or order number in
all communications.
All right reserved.